Data Center Troubleshooting
'Database is being updated by an instance which is not part of the current cluster' Error Message
Add multicast route, Check firewall, Cluster Panic due to Multiple Deployments
Error in log:
Multicast being sent, but not received
Check firewall, Check intermediate routers, Increase multicast TTL
|App is unlicensed on some nodes after updating the license on one node.||Disable and re-enable the app in the Universal Plugin Manager.|
|After an app update, strings appear in the UI instead of buttons and icons on some nodes.||Restart the affected node.|
|See Hazelcast CANNOT start on this node. No matching network interface found KB article|
Any issue not covered here
- Which multicast address?
The multicast address and port used by Confluence can be found on the Cluster Configuration page, or in
confluence.cfg.xml in the Confluence home directory.
- Multicast address generation.
Confluence uses a hashing algorithm to take the inputted name during setup and it is then turned into a multicast address stored in the config file. Thus, once the initial setup is completed, Confluence will use the address this is the reason why user can change the address if needed, without actually changing the name. Consequently the additional nodes using the same multicast address specified in the config file are able to join the cluster.
Each node has a multicast address configured in the
A warning message is displayed when an user changes the address from the one that Confluence has generated by the hashing of the name. There is no way of eliminating the message any other way other than by returning the address to the one that matches the cluster name. Purpose of the warning message is to remind the user that the address has been changed - as it is not the hashed version any longer - consequently the node can not join the cluster just by using the name. It is also necessary to provide the correct address as well.
Mapping interface to IP address.
To ensure that the interface name is mapped correctly, the following tool can be used. It shows the mapping of the interface name to the IP address.
C:\>java -jar list-interfaces.jar interfaces.size() = 4 networkInterface = name:lo (MS TCP Loopback interface) index: 1 addresses: /127.0.0.1; networkInterface = name:eth0 (VMware Virtual Ethernet Adapter for VMnet8) index: 2 addresses: /192.168.133.1; networkInterface = name:eth1 (VMware Virtual Ethernet Adapter for VMnet1) index: 3 addresses: /192.168.68.1; networkInterface = name:eth2 (Broadcom NetXtreme 57xx Gigabit Controller - Packet Scheduler Miniport) index: 4 addresses: /192.168.0.101;
Listed below are some debugging tools that help determine what the status of the multicast traffic is:
Lists multicast groups. Does not work on Mac OS X.
Lists system routing table.
Captures network traffic on the given interface. Most useful on an interface that only receives cluster traffic.
Add multicast route
Multicast networking requirements vary across operating systems. Some operating systems require little configuration, while some require the multicast address to be explicitly added to a network interface before Confluence can use it. If multicast traffic can't be sent or received correctly, adding a route for multicast traffic on the correct interface will often fix the problem. The example below is for a Ubuntu Linux system:
route add -net 188.8.131.52 netmask 240.0.0.0 dev eth0
To support multiple applications using multicast on different interfaces, you may need to specify a route specific to the Confluence multicast address.
Ensure your firewall allows UDP traffic on the multicast address and port used by Confluence.
There are known issues relating to IPv6. You should configure your JVM to try binding to an IPv4 address first.
Change multicast interface
Confluence might have selected the incorrect interface for multicast traffic, which means it cannot connect to other nodes in the cluster. To override the interface used for multicast traffic after initial setup, edit the
confluence.cluster.interface property in
<local-home>/confluence.cfg.xml and specify the network interface. For example to tell Confluence to use
Overriding Hazelcast Configuration
If the solution to your problem involves changes to the Hazelcast configuration, these changes should not be made to the Confluence configuration files. Instead, to ensure your configuration survives upgrades, make your changes by creating a Hazelcast override file.
Increase multicast TTL
The multicast time-to-live (TTL) specifies how many hops a multicast packet should be allowed to travel before it is discarded by a router. It should be set to the number of routers in between your clustered nodes: 0 if both are on the same machine, 1 if on two different machines linked by a switch or cable, 2 if on two different machines with one intermediate router, and so on.
To increase the multicast TTL by edit the
confluence.cluster.ttl property in the
<local home>/confluence.cfg.xml file on each node. For example to set the TTL to 3:
Check intermediate routers
Advanced switches and routers have the ability to understand multicast traffic, and route it appropriately. Unfortunately sometimes this functionality doesn't work correctly with the multicast management information (IGMP) published by the operating system running Confluence.
If multicast traffic is problematic, try disabling advanced multicast features on switches and routers in between the clustered nodes. These features can prevent multicast traffic being transmitted by certain operating systems.
Didn't find a solution?
Check Related Articles from the Confluence Knowledge Base
Contact Atlassian support
We have dedicated staff on hand to support your installation of Confluence. Please follow the instructions for raising a support request and mention that you're having trouble setting up your Confluence cluster.
Was this helpful?Yes Provide feedback about this article